Features:
General use for 910 binding posts.
Voltage higher than 1KV below.
Current is less than 5A.
Breadboard fixing hole dia.8mm.
4 mm banana plug can be inserted
The ACS712 Current Sensors offered on the internet are designed to be easily used with micro controllers like the Arduino.
Sensors are based on the ACS712 chip.
The basic functional operation of each of these devices is identical.
The only difference is with the scale factor at the output as detailed below.
#acs712 #currentsensor #voltagesensor
Features:
Input voltage: DC 10V-32V.
Output voltage: DC12V-35V(adjustable).
Output current: 10A (MAX).
Input current :16A (MAX) (more than 10A please strengthen heatsink).
Output power: natural cooling 100W (MAX), strengthening cooling 150W (MAX) real power.
Conversion efficiency: 94% (when Input 19V 2.5A Output 16V, Reference).
Output ripple: 2% (MAX).
Working temperature: industrial (- 40℃~+85℃) ( environmental temperature, more than 40 degrees, please reduce power to use, or - enhance cooling).
Full-Load temperature: 45℃.
No-load current: 25mA typical.
Voltage regulation: ± 0.5%.
Load regulation: ± 0.5%.
Dynamic response speed: 200uS 5%.
Short circuit protection: No (Please installs the fuse or protection circuit at input parts).
Input Reverse protection: No (please comply with a reverse protection or connect a diode at input parts.)
Dimension: 65mm x 35mm x 23.5mm.
Package Include: 1 x 150W DC-DC Boost Converter 10-32V to 12-35V Step Up Power Supply Module
Applications:
DIY an adjustable on-board power supply, you just input DC 12V, then you can get output DC 12V-35V (adjustable), But the output voltage can not below the input voltage.
DIY a booster charger. Provide power for your electronic equipment.
Use Solar battery charging for electric accumulator.
#DIYMORE #150W #DC-DC #Boost #Converter #Step #Up #Charger #Power #Module
This controller uses novel bi-directional high-power SCR.
Connect it with lamp or home appliance in a series connection, then rotate the knob for dimming, speed, voltage, temperature control.
It can be very convenient adjust the current up to 25A, and solve the over current problem of the heating wire resistance is too small in the case of cooling causing good.
The output voltage is adjusted anywhere between 50V-220V for use with electrical appliances.
It can use to such as electric stove, water heater, lighting dimmer, small motor speed, electric iron thermostat, and achieve dimming, thermostats, pressure regulator effect.
#Voltage #Regulator #2000W #Electronic #Dimmer #Power #Supply #Speed #Controller #Adjustable #Digital #Dimming #Home #Module
RC522 IC Brief Introduction :
MF RC522 is used in highly integrated 13.56MHz contactless communication card chip to read and write, of NXP for “three” and the application launched a low voltage, low cost, small size, non-contact card chip to read and write, intelligent instruments and portable handheld devices developed better.
The MF RC522 use of advanced modulation and demodulation concept completely integrated in the 13.56MHz all kinds of passive contactless communication methods and protocols. 14443A compatible transponder signal. The digital part handles the the ISO14443A frames and error detection. In addition, support Quick CRYPTO1 encryption algorithm, the term verification MIFARE series. MFRC522 support MIFARE series of high-speed non-contact communication, two-way data transfer rates up to 424kbit / s.
As 13.56MHz highly integrated card reader series chip new family, the MF RC522 MF RC500 MF RC530 there are many similarities, but also have many of the characteristics and differences. Communication between it and the host SPI mode, helps to reduce the connection, reduce PCB board volume and reduce costs.
RFID Module Brief Introduction :
MF522-AN module uses Philips MFRC522 original chip design circuit card reader, easy to use, low cost, suitable for equipment development, the development of advanced applications reader users, the need for RF card terminal design / production users. This module can be directly loaded into the variety of reader molds.Module uses voltage of 3.3V, simple few lines through the SPI interface directly with any user CPU board is connected to the communication module can guarantee stable and reliable work, reader distance.
#MFRC-522 #RC-522 #RC522 #13.56MHz #RFID #Module #For #arduino #UNO #Kit #SPI #Writer# Reader #IC #Card #IC #KEY
5V or 12V 1 Channel Relay Module Low level for DIY project.
The module uses genuine quality relay, normally open interfaces.
Fault-tolerant design, even if the control line is broken, the relay will not operate.
The interface design of human nature, all interfaces are available through a direct connection terminal leads, very convenient.
#relay #5vrelay #arduinorelay #12vrelay #module
L298N Dual H Bridge Motor Driver.
Motor controller breakout board which is typically used for controlling speed and direction of motors.
Dual-channel H-bridge driver working mode creates higher working efficiency.
L298N as main chip
It has strong driver capability, after flow protection diode, more stable and reliable
#l298n #motordriver #arduinol298n #motor #driver #l293d #dcmotor
High Quality HC--SR501 PIR Infrared Sensor Module.
PIR sensors, often referred to as, "Passive Infrared" or "IR motion" sensors, enable you to sense motion.
Everything emits a small amount of infrared radiation (IR), and the hotter something is, the more radiation it emits.
PIR sensors are able to detect a change in average IR levels of their detection zone (e.g. when a human enters a room, that room will increase in temperature slightly) and hence sense motion.
This one's great, as it can be powered via the Raspberry Pi's 5V output, and be read directly from the Raspberry Pi's GPIO input (as the sensor has a digital 3.3V output!)
This PIR includes an adjustable delay before firing (approx 0.5 - 200 seconds), has adjustable sensitivity and two M2 mounting holes.
It runs on 4.5V-20V power (or 3V by bypassing the regulator with a bit of soldering) and has a digital signal output (3.3V) high, 0V low.
Its sensing range is up to 7 meters in a 100 degree cone.
#HCSR501 #pirsensor #motionsensor
The SG90 mini servo is lightweight, high-quality and lightning-fast.
Compatible with any servo code, hardware or library.
Servo motors comes with three wires: power, ground, and signal.
Operating Voltage ~5V.
Good for beginners who want to make stuff move without building a motor controller with feedback & gear box, especially since it will fit in small places.
#sg90 #towerpro #servosg90 #sg90180 #servotowerpro #servo #towerprosg90 #RCforRC #250 #450 #Helicopter
HC-SR04 Ultrasonic ModuleDistance Measuring Transducer Sensor for arduino.
This performance of the ultrasonic sensor distance measuring module is stable, measure the distance accurately.
The module is with High precision, blind spots (3cm) super close.
This module provides a full set of ranging process.
As any ultrasound sensor, the HC-SR04 operates like a simple radar, by sending a series of pulse waves and listen to an echo.
To measure a distance, start by sending a short trigger pulse to the TRIG pin, at the same time monitor the ECHO pin until the output is HIGH and measure the pulse width.
The distance is equal to (pulse duration in seconds) * (speed of sound) / 2 where the pulse width is in unit of second and sound speed is in unit of meter/second.
Normally sound speed is 340m/s under room temperature.
To use this sensor with the Arduino simply download the srf04-library if you're using the Arduino IDE 1.0 or theUltrasound Library if your IDE version is older.
We recommend a pause of 60-100ms between each distance reading to allow the echo pulse enough time to settle.
Description :
Modeling simple and elegant.
LCD panels inline connections.
Moisture-resistant.
Strong anti-interference.
Applies to refrigerated cabinets.
Display counters.
Temperature measurement and display of various equipment.
Specification :
Temperature range: -50~ 110°C
Temperature display resolution: 0.1
Temperature measurement accuracy: ±1°C
Power: 1.5v LR44 button cell batteries (included )
Colour: black
Sampling period: 10S (or 2S, 30S, 60S)
Display Dimension: LCD view area: 35.0mm x 16mm
Product Dimension: 48mm x 28mm x 15mm
Install panel hole size: Diameter 4mm, Length 2cm
Cable length: 93cm
Package Content: 1 x Digital LCD Thermometer ,2 x LR44 button battery
Product Usage:
(1) Measuring the temperature inside and outside the car
(2) Measuring the temperature inside and outside the air-conditioned room
(3) Measuring the temperature inside and outside the refrigerator
(4) Measuring body temperature
(5) Measuring the water temperature of the fish pond
(6) Measuring the water temperature of a baby shower
#LCD Digital #Thermometer #Probe #Fridge #Freezer #Aquarium #Thermometer #Thermograph #for #Refrigerator #-50~110 #Degree
1. Operating voltage: no need to connect to any power supply, two-wire system
2. The two-wire voltage meter design, the wiring is simple, easy to install
3. When there is a slight error, you can calibrate it through the circuit board, "fine-tuning" potentiometer for calibration
#1PC #Red #Green #Blue #LED #Digital #Voltage #Meter #Voltmeter #Panel #AC #70~500V #Portable Tool
XTW6009 is a high-performance 400KHz 4A switch currency step-up (BOOST) module.
This module XL6009 is coming with the 3rd generation high-frequency switch technology as the core chip, The performance is much higher than LM2577.
Wide input voltage: 3V~32V.
Optimum operating voltage range: 5~32V.
Wide output voltage: 5V~40V.
With 4A high efficiency MOSFET switches, so the efficiency can be up to 94%, (LM2577current is 3A only).
With ultra high switch frequency 400KHz , even if small capacity filtering capacitors can achieve very good results, ripple is smaller (Compare to LM2577 frequency 50KHz).
#Arduino #XL6009 $DC-DC #Adjustable #Step-up #Voltage #Booster #Module #4A #Solar #Voltage #Board
MP1584EN DC-DC step-down power supply module 3A adjustable step-down module super LM2596 ultra-small size size DCDC.
This is a tiny DC-DC buck converter with circuit and overheats protection enable.
#MP1584EN #DC-DC #step-down #powersupply #module #3A #adjustable #step-down #module #super #LM2596 #ultra-small
This module is different from the LM2596 and XL4005 buck modules on the market. The chip design power used by them is 15W and 50W.
The upgraded chip has both input and output voltage range, output power and efficiency.
To be better than similar products, the power can reach 75W, with a very high cost performance.
#Module #XL4015E #5A #High-Power #75W #DC-DC #Adjustable #Buck #Module #Display #LED #Power #Regulator #4.0 ~ 38V #1.25V ~ 35V #Hardware #Laptops #Computers